我公司生产超高压时序控制系统，单时序双时序，液压控制，为模内热切设备提供动力。主控界面可操作a、模式选择：生产模式为正常生产模式；测试模式无控制信号可以动作，可以点动测试。b、输出压力显示c、设置输出压力，设定切刀切断压力，无需手动调节，设置后会自动调节压力。d、电机启动停止按钮e、页面选择按钮f、各路开关按钮，厂商登录界面可锁定各个开关，默认开启第一路。g、等待时间：时序控制器接收到信号后等待的
我公司生产超高压时序控制系统，单时序双时序，液压控制，为模内热切设备提供动力。
Our company manufactures ultra-high-pressure timing control systems—single-sequence and dual-sequence models—with hydraulic control, providing power for in-mold hot-cutting equipment.
主控界面可操作
a、模式选择：生产模式为正常生产模式；测试模式无控制信号可以动作，可以点动测试。
b、输出压力显示
c、设置输出压力，设定切刀切断压力，无需手动调节，设置后会自动调节压力。
d、电机启动停止按钮
e、页面选择按钮
f、各路开关按钮，厂商登录界面可锁定各个开关，默认开启第一路。
g、等待时间：时序控制器接收到信号后等待的时间，这段时间后推出切刀油缸。
h、切模时间：油缸切刀推出后，保持在模具内部的时间，这段时间后，切刀油缸退回。
i、班组切模：累计此次开机状态切模数量，可清零。
j、累计切模：时序控制器累计切模数量，厂商登录可清零。
k、点动开关：控制电机点动，点动切模，电机卸载，低压卸压。
l、合模信号启动/开模信号启动切换功能。
注意：设置压力不得超过100MPa，大于该值会提示，并停止运转。
设置时间不得小于0.5秒，小于该值会提示，并停止运转。
生产模式操作步骤：选择生产模式-启动电机-设置压力-设置等待时间-设置切模时间-打开相应路数开关
Main Control Interface Functions
a. Mode Selection: Production mode is the normal production mode; in test mode, the system operates without control signals and supports jog testing.
b. Output Pressure Display
c. Set the output pressure and the cutting pressure for the blade. Manual adjustment is not required; the pressure will be automatically adjusted after setting.
d. Motor Start/Stop Button
e. Page Selection Button
f. Channel Switch Buttons: The manufacturer login interface can lock individual switches; by default, Channel 1 is enabled.
g. Wait Time: The delay period after the sequencer receives a signal; the cutter cylinder extends after this time.
h. Cutting Time: The duration the cutter cylinder remains inside the mold after extending; the cutter cylinder retracts after this time.
i. Shift Cutting Count: The cumulative number of cuts made during the current machine operation; can be reset.
j. Cumulative Cutting Count: The cumulative number of cuts recorded by the sequencer; can be reset via the manufacturer login.
k. Jog Switch: Controls motor jog operation, performs a single-cycle cut, unloads the motor, and releases low-pressure.
l. Toggle function between Clamping Signal Start and Unclamping Signal Start.
Note: The set pressure must not exceed 100 MPa; exceeding this value will trigger a warning and stop operation.
The set time must not be less than 0.5 seconds; setting a value below this will trigger a warning and stop operation.
Production Mode Operating Steps: Select Production Mode – Start the motor – Set the pressure – Set the wait time – Set the cutting time – Turn on the corresponding number of switches
