Notes on Booster Valve Usage？
像增压阀这些东西基本上都是工业领域用的产品，大多数我们都没有见过也没有听过，你可以说在生活中并不是很常见，但是它们在工业行业中也是发挥着不可替代的作用，那么我们在使用中首先要了解清楚的就是增压阀的使用注意，接下来就跟着我们一起来了解一下吧。
Booster valves are industrial products rarely seen in daily life, yet they play an irreplaceable role in industrial production. It is essential to master relevant precautions before use. Let's take a look at them.
增压阀应该水平安装;增压阀出口压力超过1.0MPa，应确认管接头、管道、阀门、气缸等的工作压力范围;在特殊情况下，需要迅速排出残压，可在适当位置加装三通阀，为缩短储气罐充满时间，可将增压阀并联使用单向阀。
The booster valve shall be installed horizontally. If outlet pressure exceeds 1.0MPa, verify the working pressure rating of pipe joints, pipelines, valves and cylinders. A three-way valve can be mounted for quick residual pressure relief when needed. Booster valves can be installed in parallel with check valves to shorten gas tank charging time.
增压阀手动二位三通换向阀可迅速排出缸内余压。气罐内压力充至p1前，仅通过单向阀充气。如果并联单向阀，储气罐内的压力需要通过增压阀才能充到p1.所以充时间长。输出压力相对于自己需要的压力要有余量。高压入口处比较好的就是加装过滤器，有利于减少杂质对产品的影响。产品入口压力有严格要求，入口压力过低，直接影响气体增压泵的流量和输出压力。驱动气压范围≤8bar，切勿超载。增压阀的承压介质的洁净度、气体增压阀的洁净卫生和现场使用环境。使用前，建议在驱动气源口加装油水分离器，经常放出杯内水分。每个高压气体增压阀用完后，需要排出高压气体。定期检查气体增压阀以保持组件完整性。
The manual two-position three-way directional valve can quickly release residual pressure inside the cylinder. Before the air tank pressure reaches p1, inflation is only conducted through the check valve. Parallel installation of check valves will prolong inflation time as gas has to pass through the booster valve. Reserve proper pressure margin for actual output demand. A filter installed at the high-pressure inlet effectively reduces damage caused by impurities. Strict inlet pressure requirements apply; insufficient inlet pressure impairs flow rate and output pressure. Driving air pressure shall not exceed 8 bar and overloading is forbidden. Ensure clean pressure medium, valve cleanliness and favorable operating environment. Install an oil-water separator at the air inlet and drain accumulated water regularly. Discharge residual high pressure after each use. Conduct routine inspections to keep all parts intact.
增压阀的增压缸内的油雾通过气管进入电磁阀，导致管内有尘粒等杂质，连接管内生锈介质在使用过程中发生变化。拆卸电磁阀清洗时，可用煤油、三氯乙烯等溶液，但应注意橡胶件可能会膨胀，故更换橡胶件时不应拆卸电磁阀线圈总成。增压阀在清洁时，应将零件放好，以便恢复安装。空压机的油会氧化产生碳粒、焦油等杂物，混入管路中。经过多次试水运行，工作正常后方可投入运行。不应拆卸电磁阀线圈组件才能正式的去使用它。
Oil mist inside the booster cylinder flows into the solenoid valve via air pipes, bringing dust particles and rust contaminants that deteriorate during operation. Kerosene or trichloroethylene can be used to clean disassembled solenoid valves. Note that rubber parts may swell, so avoid removing the coil assembly when replacing rubber components. Keep parts properly arranged during cleaning for easy reassembly. Oxidation of air compressor oil produces carbon particles and tar impurities inside pipelines. Conduct repeated test runs and confirm normal performance before formal operation. Do not disassemble the solenoid valve coil assembly in use.
我们公司坚持用户至上质量为上的原则，一如既往为各企业提供更好的产品、更好的服务，并且愿意为国家的环保事业做出更大的贡献。希望衷心关心和支持本公司事业的各界朋友，能提供更多的合作机会。以上文章内容就是增压阀厂家为你讲述产品的基本信息，不知道你了解了没有呢。如果你还不了解的话赶紧来阅读一下吧。好了，今天的知识点就先说到这里了，希望能为你带来帮助吧。
Our company adheres to the principle of customer and quality priority. We keep delivering superior products and services to enterprises, and commit to contributing more to environmental protection. We welcome cooperation opportunities from all partners. The above is basic information about booster valves. Feel free to look through the content for more details. We hope this introduction brings you practical help.